The Wavlink Aerial HD4 Outdoor Extender Setup is a dual-band wifi range Extender that assists you in simply removing all dead zones from your location. And provides up to 600 megabits per second.

The Wavlink Aerial HD4 is intended for WISP CPE and long-distance wireless networks, making it ideal for small offices, homes, and businesses that demand outdoor networking. A powerful outdoor Wi-Fi range extender with a user-friendly design and specialist performance.

The Wavlink Aerial HD4 Outdoor Setup is covered by a one-year warranty.

In case you are still facing an issue and need any guidance regarding your Wavlink Extender Setup

How to install Wavlink Aerial HD4 Outdoor Extender?

This section explains how to set up the Wavlink Aerial HD4 Outdoor Extender.

Our Wavlink Aerial HD4 Outdoor Setup can be installed in three ways.

1.Router 

2.Repeater

3.The Lan Bridge

How do you use the Router mode to configure your Wavlink Aerial Outdoor Extender?

Repeater mode is the most straightforward method of installing yourWavlink Aerial Outdoor Extender setup.

To install your Wavlink Outdoor Extender, carefully read the instructions below.

  • Connect your Wavlink AC1200 connection (POE) box to a power outlet.
  • Connect the ethernet cable from the POE box to the Aerial HD4 extender.
  • Connect the other ethernet connection to your main router using the same connector box.
  • Connect to the WAVLINK-N network using any wirelessly capable device.
  • After you've connected, open a web browser and go to wifi.wavlink.com.
  • You've arrived at the AC1200 outdoor extender setup page.
  • Use the "admin" default password to log in.
  • Give your booster a distinctive name and select the "Router" option.
  • Modify the safety to WPA2-PSK from none ( recommended ). After that, enter your extender's password and press "Next."

Your  Wavlink Aerial HD4 Outdoor Extender Setup  has been successfully done 

How do I configure the Wavlink Aerial HD4 Outdoor Extender in Repeater mode?

To install your Wavlink Aerial HD4 Outdoor Extender Setup follow the given steps

  • To begin, connect the Wavlink AC1200 connection (POE) box to a power outlet.
  • After the AC1200 signal changes to green, connect the POE's ethernet connection to the extender.
  • Take out any wirelessly enabled device, such as a laptop or smartphone.
  • Examine the wireless settings for the network WAVLINK-N.
  • Open any web browser, including Internet Explorer, Google Chrome, Mozilla Firefox, and Safari.
  • In the search bar, enter Default IP Address 192.168.10.1 or your Extender's Web address ap.setup.
  • Enter your password.
  • You have arrived at the Wavlink Aerial HD4 Outside Extension Setup configuration page.
  • Use the "admin" default password to log in.

The Wavlink Aerial HD4 Outdoor Extender Setup  has now been done as a repeater.

Remember that if you want to use your extension as a repeater, you cannot connect any cables from the POE to the primary router/modem.

If you are facing any kind of issue during Wavlink Aerial HD4 Outdoor Extender Setup feel free to Contact our technicians for guidance

 Firmware update

Firmware is made up of both hardware and software. The firmware is a set of software that is built into hardware. To help solve any issues (such as not offering enough speed or something else) that you may encounter while using your extender, you must update the firmware on your Wavlink AC1200. It has more security features as well as other new features that will help you find solutions to your issues.

How do I update the firmware on my Wavlink Aerial HD4 Outdoor Extender?

Follow the steps below to update the firmware on your Wavlink AC1200:

  • Turn your Wavlink Aerial HD4 on.
  • Take out any mobile device.
  • Enter ap.setup in the search bar.
  • Choose settings, then firmware upgrade.
  • Follow the instructions to complete the firmware update procedure.
  • It will take a minute; however, do not unplug the booster until the procedure has finished.

How to reset Wavlink Aerial HD4 Outdoor Extender?

If you have forgotten your admin password or username and would like to recover it. You must perform a booster factory reset. It will remove all of your personal data, including passwords, usernames, and SSIDs, to prepare your extender for a new setup process. To complete the factory reset procedure, a hard pointed object, such as a paperclip or a needle, is needed.

To Reset Wavlink Aerial HD4 Outdoor Extender follow the steps below:

  • Connect your Wavlink AC1200 to an electric socket.
  • Under a small hole, locate the factory reset button.
  • It could be found on the repeater's side panel.
  • Take the paper clip and hold it up to the reset button for 8 to 10 seconds.
  • It will restart automatically after a few seconds.

If you are facing any kind of issue during Wavlink Aerial HD4 Outdoor Extender Setup feel free to Contact our technicians for guidance